Just How to Install a Bathtub: Set Up an Acrylic Tub and Also Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Tub and Also Bathtub Surround
Blog Article
Just how do you really feel in regards to How to Install a Bathtub?
Setting up a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is conveniently available, the task can move easily; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the job is within a house handyman's abilities, although you will require a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have actually certified yourself for the work and fit attempting it. Instead of working with a specialist to take control of a halfway-completed project, it is far better to consider utilizing one prior to you begin. Opportunities are you may require a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your shower room if you have actually currently purchased a new bathtub and don't require to change the plan of your previous water pipes.
Your tools and also material checklist need to comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted gain access to that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the faucet as well as the sink. Secure the tap in position with the supplier supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Tub
Utilizing both wood boards under its feet, place the bath tub in the needed position. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bathtub till the spirit level checks out degree.
To set up taps, fit all-time low of the furthest adaptable faucet connector to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water system and inspect all joints and also new pipework for leakages and tighten them if essential. Fill up the bath tub and additionally check the overflow outlet as well as the regular outlet for leakages.
Finally, deal with the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait until the bath tub has actually been made use of a minimum of when as this will certainly settle it right into its last position.
Planning for the Installation
First of all, the sustaining frame provided with the bath should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of both faucets using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, causing issues with dampness and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to allow for the movement experienced when the bathtub is in use. The sealer can crack rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads about How to Install a Bathtub, I figured sharing that portion was smart. Make sure you take the time to share this page if you enjoyed it. Many thanks for taking the time to read it.
Get A Free Quote
Report this page